| LED Models | Incandescent Models |
|---|---|
| 9550 | |
| 9650 | |
| 9651B | |
| 9652B |
The Nevco six court Tennis control system consists of one receiver and six hand-held controls. Each control can post information on the scoreboard for the court it has been assigned to.
MPCX2 Receiver for use with outdoor x6xx and indoor x7xx scoreboards.
MPCX2 Receiver for use with scoreboards that pre-date x6xx outdoor and x7xx indoor scoreboards. (Boards that have coax input only)
The Nevco six court tennis scoreboard system consists of six wireless hand held controls (one for each court) and one scoreboard that displays the scores for all six courts, plus the total score. Each control can send information to the scoreboard for its corresponding court for both teams for 3 sets of play and total score.
The Nevco single court tennis system operates the same way as the six court system. The main aspect is that the single court controller must be set to court 1.
Any of the controls can be programmed to control any of the six courts, including court 1. Multiple controllers can be set to the same court. The controller designated as court 1 is the only controller that can control the brightness level or clear the whole scoreboard at once.
Turn the scoreboard power ON first. Wait approximately 10 seconds before turning the controls on and make sure each controller is initialized before powering on the next controller. Verify the court that each control is configured to operate.
- Press ON/OFF — The control will display a greeting while it establishes communications with its receiver(s). (Up to 20 seconds).
> Display: MPCX2 v01.00 / 2.4 GHz
> Then: Scanning
- The display will then show Total Score.
> Display: Total Score / Home: _ Guest:
- Press SET 1 — Next the display will change to show:
- The Court number the control is programmed to operate
- The Set number
- The Home score
- The Guest score
> Display: Court: 1 Set: 1 / Home: _ Guests:
- Press OPTIONS
- From the Options Menu, select:
Clear Scoreboard / Press (+) - Then press +
This will clear all of the scores for all of the courts.
- Press OPTIONS
- From the Options Menu, select:
Clear Court: 2 / Press (+) - Then press +
Using the court 2 controller, this will clear the scores for only court 2.
- Press SET 1 — The control will show:
> Display: Court:1 Set:1 / Home:0 Guests:0
- Use the HOME or GUESTS keys to select the team.
> Display (HOME selected): Court:1 Set:1 / Home:0 Guests:0 (cursor under Home)
> Display (GUESTS selected): Court:1 Set:1 / Home:0 Guests:0 (cursor under Guests)
- Use the + or − keys to enter the points.
> Display: Court:1 Set:1 / Home:1 Guests:0
You are now ready for the game to begin.
Please consult the following sections of this manual for more details, functions, and features.
GREETING
When the control is Powered ON, the greeting shows the type of control, the software version, and the frequency it is broadcasting. It will then display scanning for the remaining time until the control establishes communications with its receiver(s). (May take up to 20 seconds)
Display:MPCX2 v01.00 / 2.4 GHzThen:Scanning
Accessed by pressing: ON/OFF
Press ON/OFF when you are done using the control; power it OFF to conserve batteries.
TOTAL
This is the default screen on power up. This screen shows the Total Score. You must use this screen if you want to change the Total Score. The cursor indicates the currently selected team. Use the HOME or GUESTS keys to select the team, then, use the "+" or "−" keys to change its value and send it to the scoreboard.
Display: Total Score / Home:2 Guests:1Accessed by pressing: TOTAL
Use the "TOTAL" key if you want to change the Total Score. Select Home or Guests, then, use the "+" or "−" keys to change the Total Score and send it to the scoreboard.
MAIN
The main screen shows the Court Number, the Set Number, and the Scores. You must use this screen if you want to change the Scores. Press SET 1, SET 2, or SET 3 any time to return to its screen. The cursor indicates the currently selected team. Use the HOME, GUESTS, keys to select the team, then, use the "+" or "−" keys to change its value and send it to the scoreboard. You should keep one of these three screens displayed during the game.
Accessed by pressing: SET 1, SET 2, or SET 3
Display (Set 1):Court:1 Set:1 / Home:1 Guests:1Display (Set 2):Court:1 Set:2 / Home:1 Guests:1Display (Set 3):Court:1 Set:3 / Home:1 Guests:1
- Press SET 1 — Select Set 1.
> Display: Court:1 Set:1 / Home:1 Guests:1
- Press SET 2 — Select Set 2.
> Display: Court:1 Set:2 / Home:1 Guests:1
- Press SET 3 — Select Set 3.
> Display: Court:1 Set:3 / Home:1 Guests:1
- Press HOME or GUESTS — Use the "Home" or "Guests" keys to select the team whose score you want to change.
> Display (HOME selected): Court:1 Set:1 / Home:1 Guests:0
> Display (GUESTS selected): Court:1 Set:1 / Home:1 Guests:0
- Press + or − — Use the "+" or "−" keys to change the selected teams score and send it to the scoreboard.
> Display: Court:1 Set:1 / Home:1 Guests:1
GAME SCORE (Only applicable to 9652)
Game Score
The game score shows a cursor to indicate whether it is currently set to change home or guest game score. Game score can be incremented and decremented using the + and – keys. The score increments in 15, 30, 40 (dc will be displayed if opposite team is also at 40) and Ad. The game score must be decremented back to 00 for both teams in order to clear the game score between sets.
Accessed by pressing: GAME
Display: Game Score / Home: 00 Guest: 00- Press HOME or GUESTS — Use the "Home" or "Guests" keys to select the team whose score you want to change.
> Display (HOME selected): Game Score / Home: 00 Guests: 00
> Display (GUESTS selected): Game Score / Home: 00 Guests: 00
- Press + or − — Use the "+" or "−" keys to change the selected teams score and send it to the scoreboard.
> Display: Game Score / Home: 15 Guests:15
SERVE (Only applicable to 9652)
Serve
The serve indicator shows the team that is currently serving. Serve is modified using the Home and Guest buttons.
Accessed by pressing: SERVE
Display: Serve / Home: < Guest:Use the "Home" or "Guests" keys to select the score indicator.
- Press HOME:
> Display: Serve / Home: < Guest:
- Press GUESTS:
> Display: Serve / Home: Guest: <
Several option settings are available to fine tune the scoreboard system to your needs. These settings are saved in the control. They are remembered even if the control is turned OFF or the batteries removed. When a control turns ON the scoreboard, these settings are sent to the scoreboard and are used to define how it operates. This allows each coach or group to have their own control with its unique option choices, thus eliminating the need to set up the options every time the scoreboard is used. For example, Brightness (Baseball – day time) (Soccer – night time).
It is also possible to use more than one control to operate the scoreboard. For instance, the Time can be controlled by one person while someone else operates the rest of the scoreboard with another control.
The options key can be used to access the following features. Each press of the options key moves you to the next option screen.
Clear Scoreboard / Press(+)
Allows you to clear the scoreboard data.
Reset Game / Press(+)
Allows you to clear the HOME and GUESTS Game Score.
Tie Break Score / (+)YES (-)NO
Allows you to set the mode of scoring to Tie Break mode.
In Tie Break scoring mode, points for each player are incremented by one instead of 15, 30 & 40.
Clear Court: 1 / Press(+)
Allows you to clear individual court that the controller is set to.
Edit ETN / Press(+)
Allows you to edit the Electronic Team Name for both Home and Guest.
Use the "+" to go increment the alphabet and the "−" key to decrement the alphabet. Use the "Options" button to advance the cursor.
Sub-screens:Guests ETN / Press (+)Home ETN / Press (+)Home ETN / _
Brightness / (+)HIGH (-)LOW
Allows you to select the Brightness Level of the scoreboard. (High or Low)
Battery Level / L>>>>>>>>>>>>H
Reports the condition of the batteries in the control.
Signal Strength / L>>>>>>>>>>>>H
Allows you to check signal strength when connected to a receiver. Used as an indication of reliability of communications. Affected by distance, battery condition, obstructions and signal interference.
Enter Code to Change Settings
This menu option allows you to access settings that affect how the control operates. Generally, these settings need not be changed and should only be changed by an experienced operator or under direction from the Nevco Service Department.
Press the following key sequence: HOME → + → − → GUESTS
- a. Segment timer - (Segment time) (+) (−) (Auto Horn)
- b. Shot Clock/Pitch Time/Delay Of Game - (Reset 1) (+) (−) (Reset 2)
to gain access to the following additional menu items.
Or
Press the OPTIONS key to return to the main screen.
Link Menu / Press (+)
This menu option allows the user to add a receiver ID, delete a receiver ID, and to view the status of which ID's are programmed and enabled or disabled. Press the + button to scroll through the different link menus.
Please refer to sections "Mating a New Control to Receiver(s)" and "Adding, Deleting or Enabling/Disabling Receiver ID's" for detailed instructions.
The Network Analyzer allows the user to see the number of receivers connected and see the integrity of the network in percentage.
Sub-screens:Add a Rec ID / Press (+)Delete a Rec ID / Press (+)View Rec ID's / Press (+)Network Analyzer / Press (+)
The next press of the options key will display one of the following screens. It indicates which of the scoreboard model series the control is currently configured to operate. Use the "+" key to toggle thru the scoreboard models. Press the OPTIONS key again to exit the options routine. The last scoreboard series displayed will become the new control configuration.
Scoreboard Model
Refer to the Scoreboard Model table found below for the appropriate scoreboard model to be used with your scoreboard.
One option that is only found in tennis MPCX2 controllers is listed below.
The options key can be used to access the following features. Each press of the options key moves you to the next option screen. The change court controller option is located after the advanced options.
Current Court: 1 / New Court: 2
This will change the court that the controller is controlling. Use the "+" and "−" keys to increment or decrement the desired court.
Before using the MPCX2 control it must be mated to the receiver(s) and set for the model of scoreboard that you wish to operate.
- Record the receiver(s) ID's located on the receiver box before installation for future reference. Multiple receivers can be used with multiple controllers all on the same network.
- Install the receiver(s) into the scoreboard and power up the receiver(s) that are to be used.
- a. Standard Installation – Uses the RJ12 output of the receiver.
- b. Rain Type Box Installation – Uses the coax output of the receiver and a 9VDC power supply.
- Wait approximately 15 seconds after the receiver has been turned on before turning on the MPCX2 controller in order to allow enough time for the receiver to be initialized.
- Insert the batteries included with the MPCX2 control or turn the control ON by pressing ON/OFF.
The display will read: Enter Rec ID: / 000000
- Enter in the receiver ID's located on the receiver box using the controller keypad buttons Options (NEXT) to move the cursor and + or − to increment or decrement each digit.
When done press the (BACK) button in the lower left corner.
- The screen will then prompt with:
Reset Now? / (+)NOW (-)LATER - Pressing + will reset the controller. Pressing − will allow additional receiver ID's to be entered into the controller and will display the message:
Add Another? / (+)YES (-)NO - If additional receivers are to be added then select + and repeat steps 5 through 6. If additional receivers do not need to be added then select − and the controller will be reset.
Record Receiver ID's Here: ___________________________
This procedure is not necessary if you have one of the following models:
1500, 1510, 1530, 1535, 1550, 1600, 1610, 1630, 1635, 1650, 1000, 1010, 1030, 1035, 3500, 3502, 3504, 3514, 3515, 3516, 3520, 3525, 3534, 3550, 1632, 9605, 9505, 9715, 9515, 3400, 3402, 3404, 3414, 3415, 3416, 3425, 3434, 9405, 9550, SCD-5, SCD-7, S60-LED, S60, SCD-4.
And for any sport except Soccer: 2700, 2710, 2715, 2740, 2750, 2760, 2770, 2775, 2600, 2610, 2615, 2640, 2650, 2670, 2675, 2500-D, 2500, 2500-A4-D, 2500-A4, 2540, 2540-A4, 2550-D, 2550, 2560, 200, 230, 9510, 9715, 9515, 9710, 2400, 2400-A4, 2440, 2440-A4, 2450, 2460, 9410
- Turn the control on by pressing ON/OFF
- Press the Options button until the display reads:
Enter Code to Change Settings - Enter the "Code" with the buttons in the sequence HOME → + → − → GUESTS
- a. Segment timer - (Segment time) (+) (−) (Auto Horn)
- b. Shot Clock/Pitch Time/Delay Of Game - (Reset 1) (+) (−) (Reset 2)
- Continue pressing the Options button until the display reads:
Scoreboard Model / (+) - Press the + key to select the scoreboard model shown in the table below.
- Press the Options key to exit the menu.
Both multiple controllers and receivers can be on the same network.
For example, one person with a controller can control Game Time and another person with a separate controller can control Game Score of the same game on the same scoreboard. Multiple controllers can be used for any combination of game data.
If a second controller is powered on after the first powered on controller has been initialized, then the second controller will be configured with the same Scoreboard Model described in the "Setting the Control for Your Model of Scoreboard" section.
Multiple receivers can be used on the same network. One example could be separate scoreboards for the same game or in the case of basketball one receiver controls the scoreboard while other receiver(s) control the shot clock(s).
| MPCX2 Control | Scoreboard Model | Screen to Select |
|---|---|---|
| Football | 3500, 3502, 3504, 3514, 3515, 3516, 3520, 3525, 3534, 3550, 1632, 9605, 9715, 9505, 9515, 3400, 3402, 3404, 3414, 3415, 3416, 3425, 3434, 9405 | Type A (+) |
| Football | 7504, 7505, 7516, 7520, 7524, 7525, 7530, 9505, 9515, 7404, 7405, 7416, 7424, 7425, 7430, 9405, 3602, 3604, 3614, 3615, 3616, 3617, 3618, 3619, 3620, 3621, 3625, 3634, 3650, 3655, 3656, 7604, 7614, 7624, 7605, 7615, 7625, 7616, 7620, 7630, 7631, 7632 | Type B (+) |
| Football | All 36XX, 76XX, and 86XX boards | X6XX (+) |
| Football | 3680, 3685, 3688, 7680, 7685 (Reorders Intelligent Caption to Ball On, Down, To Go, Quarter) | X6XX Legacy (+) |
| Soccer | 1515, 9505, 9515, 1615, 1632, 9605, 9715, 1415 | Type A (+) |
| Soccer | 1520, 1525, 9505, 9515, 1620, 1625, 9605, 9715, 1020, 1025, 9405, 9410 | Type B (+) |
| Soccer | 3502, 3504, 3514, 3515, 3516, 3520, 3525, 3534, 3550, 3555, 9605, 9505, 9715, 9515, 3402, 3404, 3414, 3415, 3416, 3425, 3434, 3455, 9405 | Type C (+) |
| Soccer | 7504, 7524, 9505, 9515, 9605, 9715, 7404, 7405, 7424 | Type D (+) |
| Soccer | 7604, 7605, 7614, 7615, 7616, 7620, 7624, 7625, 7630, 7631, 7632, 3600, 3602, 3604, 3614, 3615, 3616, 3617, 3618, 3619, 3620, 3621, 3625, 3634, 3650, 3655, 7505, 7516, 7520, 7525, 7530, 9505, 9515, 9715, 7405, 7416, 7425, 7430, 9405, 9410, 3680, 3685, 3688, 7680, 7685, 8601, 8602 | Type E (+) Supports Intelligent Captions |
| Soccer | 200, 230, 24xx, 25xx, 26xx, 27xx, 9510, 9515, 9710, 9715 | Type F (+) |
| Soccer | 3656, 3657 | Type G (+) Supports Intelligent Captions |
| Soccer | 4455, 4465, 4755, 4555, 4565, 4765, 9710, 9715 | Type H (+) |
| SCD / DGT / PCD | SCD-5, SCD-7A, SCD-T7A, SSC-7, SSC-T5, SSC-T9, S60-LED, S60, SCD-4 | Shot Clock (+) |
| SCD / DGT / PCD | DGT-6 | Delay Of Game (+) |
| SCD / DGT / PCD | DGT-5, DGT-2, 3020 | Legacy DOG (+) |
| SCD / DGT / PCD | SEG-14, SEG-18 | Segment Timer (+) |
| SCD / DGT / PCD | 9520, 9620 | Pitch Timer (+) |
| Tennis | 9550 Set one control to each of 6 courts => | Standard / Current Court: 1 / New Court: 2 |
| Tennis | 9650 Set one control to each of 6 courts => | Standard / Current Court: 1 / New Court: 2 |
| Tennis | 9651B | Standard / Current Court: 1 / New Court: 2 |
| Tennis | 9652B | Standard / Current Court: 1 / New Court: 2 |
| MPCX2 Control | Scoreboard Model | Screen to Select |
|---|---|---|
| Baseball | 1000, 1010, 1030, 1035, 1500, 1510, 1530, 1535, 1550 | Standard (+) |
| Baseball | 1003, 1006, 1503, 1506, 1508, 1540, 1603, 1604, 1606, 1608, 1609 | Score by Inn (+) |
| Baseball | 1020, 1025, 1515, 1520, 1525, 9505, 9515, 9605, 9715 | With Timer (+) |
| Baseball | 1615, 1620, 1625, 1632, 3656, 3680, 3685, 3688, 7616, 7680, 7685, 8601, 8602 | X6XX Timer (+) |
| Baseball | 1600, 1609, 1610, 1630, 1635, 1640, 1650, 3656, 3680, 3685, 3688, 7680, 7685, 8601, 8602 | X6XX Standard (+) |
| Baseball | 1603, 1604, 1606, 1608, 1609 | X6XX by Inn |
| Pitch Count | PCD-(A, 08, 10, 16, 18) With Models 1000, 1010, 1030, 1035, 1500, 1510, 1530, 1535, 1550 | Standard (+) |
| Pitch Count | PCD-(A, 08, 10, 16, 18) With Models 1003, 1006, 1503, 1506, 1508, 1540, 1603, 1604, 1606, 1608, 1609 | Score by Inn (+) |
| Pitch Count | PCD-(A, 08, 10, 16, 18) With Models 1015, 1020, 1025, 1515, 1520, 1525, 9505, 9515, 9605, 9715 | With Timer (+) |
| Pitch Count | PCD-(A, 08, 10, 16, 18) With Models 1615, 1620, 1625, 1632, 3656, 3680, 3685, 3688, 7616, 7680, 7685 | X6XX Timer (+) |
| Pitch Count | PCD-(A, 08, 10, 16, 18) With Models 1600, 1609, 1610, 1630, 1635, 1640, 1650, 3600, 3656, 3680, 3685, 3688, 7680, 7685 | X6XX Standard (+) |
| Basketball, Volleyball, Wrestling, or Hockey | No setting required | Type A (+) |
| Segment Timer | 27xx, 26xx, 25xx, SEG-14, SEG-18, 9710, 9510, 200, 230, SSC-7, SSC-T5, SSC-T9, SCD-7A, SCD-T7A, SCD-T5, SCD-5, SCD-4, 9715, 9515, S60-LED, S60, 4755, 4555-D, 24xx, 9410 | Type A (+) |
| Segment Timer | 3500, 3502, 3504, 3514, 3515, 3516, 3520, 3525, 3534, 3550, 36xx, 1632, 9605, 9505, DGT-6, DGT-5, 9405, 3020, 3400, 3402, 3414, 3415, 3416, 3425, 3434, 3455, 9515, 9715 | Type B (+) |
| Segment Timer | 36xx, 76xx, 7504, 7505, 7516, 7520, 7524, 7525, 7530, 9605, 9505, DGT-6, DGT-5, 9405, 7404, 7405, 7416, 7424, 7425, 7430, DGT-2, 9515, 9715 | Type C (+) |
| Segment Timer | 1520, 1525, 1515, 9505, 1620, 1625, 1615, 9605, 9715, 9405, 9515 | Type D (+) |
| Segment Timer | SEG-14 and SEG-18 Segment Time only | Type E (+) |
| Segment Timer | SEG-14 and SEG-18 Segment Number only | Type F (+) |
| Segment Timer | All X6XX boards with timers | X6XX (+) |
| Problem | Cause | Solution |
|---|---|---|
| Scoreboard will not turn ON when control is turned ON | Receiver not working or receiver/scoreboard not powered up | Cycle power to receiver/scoreboard |
| Scoreboard will not turn ON when control is turned ON | Control signal weak — Battery level low | Replace batteries |
| Control continues to search after an unusually long time | Check signal strength (see Options menu) — Control in a poor location | Make sure the control is in clear line of sight of the scoreboard |
| Control continues to search after an unusually long time | Out of Range | Move closer to scoreboard |
| Data won't change on control | Control is linked to extra unwanted receivers or wanted receivers are not powered ON. | Use the Options Menu to check the receivers the control is linked to and the receivers on its list. |
| Control display shows incorrect information | Control is not linked to this scoreboard | Find and use the control for this scoreboard. |
| Cannot turn the time ON | Control is not linked to this scoreboard | Link the control to this scoreboard or group (see Options Menu) |
| Control display shows incorrect information | Didn't sync up | Power control OFF, then ON |
| Control is ON but scoreboard/timer is OFF (data is changing on control) | No power to scoreboard | Check all switches, breakers, and fuses |
| Control is ON but scoreboard/timer is OFF (data is changing on control) | Bad connection between Receiver and scoreboard module | Check all cables and connections |
| Scoreboard/timer is ON but does not respond to control | Control and receiver are not communicating | Turn control OFF, then ON to establish communications |
| My control will not operate scoreboard (Out of Range) | Poor connection with bad line of sight to the scoreboard or distance is too great. | Return to a closer location with direct line of sight and verify Signal Strength and run Network Analyzer to determine and document connection integrity. If that does not work then cycle power to controller. |
| I cannot set the time | The time is running | Stop the time first |
| Cannot turn the time ON | Time at 0.0 and set to count down | Set some time on the clock |
| Scoreboard is ON – Control is OFF | Batteries were removed while scoreboard ON | Install batteries -- power ON |
| Scoreboard is ON – Control is OFF | Batteries were completely discharged while scoreboard is on | Cycle power at scoreboard |
| Not all controls of a multi-control scoreboard system will operate the scoreboard | Multiple controllers were powered on at the same time and not all connected | Power cycle the controllers that are not operating the scoreboard. |
| Scoreboard connected to MPCX2 is displaying data in the wrong places, incorrect data, or horn constantly sounds. | Control is not configured for correct scoreboard model series | Reconfigure the control (see options menu) |
If the problem persists please contact the Nevco Service Department.
800-851-4040 or https://support.nevco.com/contact/
The receiver has a red status LED next to the RJ12 and Ethernet jack. It can be used to diagnose the status of the MPCX2 receiver.
| LED Status | MPCX2 Connection Status |
|---|---|
| Solid On | The receiver is powered on, but a connection attempt has not yet been made, or a connection attempt was unsuccessful. |
| Blinking Fast (multiple times a second) | The receiver is in the network and connected. The receiver may appear to not be blinking due to it blinking very quickly. If the receiver is connected to Scorbitz through the Ethernet jack, then it will blink more visibly. |
| Blinking Slow (approximately once a second) | The receiver is not connected but connection attempts are being made. Each slow blink is a connection attempt. If the receiver is intended for the network and it is flashing slowly but never connects then verify that the receiver list in the MPCX2 control is correct. |
| Solid Off | The receiver is not powered on. It is also possible that the receiver is powered on but for some reason the LED has been turned off. If this is suspected to be the case then cycle power to the receiver and the LED should turn on after a brief delay. |
On powerup the receiver connected to the OCM will identify itself by flashing from the most significant 2 digit numbers to the least significant 2 digit numbers. For example, a receiver with ID 123456 will flash 12, 34, and then 56 on power up. This is used to distinguish which X2 receiver is connected to which OCM's without having to open up the scoreboard.
- Small and light weight (fits in or clips to pocket)
- Electronic Team Name and Caption Support
- Tactile confirmation of key pressed
- High visibility transflective display
- Convenient wireless operation
- Built in wireless signal strength meter
- Power conservation circuitry
- Built in battery meter
- Long battery life
- Uses inexpensive, readily available AA batteries
- Sealed keyboard
- No slip grip
- Ergonomic single hand operation
- Internal antenna
- Mate multiple controls to same scoreboard
- Operate multiple scoreboards
- Retrofits to existing wired installations
| Specification | Value |
|---|---|
| Size | Approximately 3¼" x 5½" x ⁷⁄₈" |
| Weight | 5½ oz. (including batteries) |
| Keypad | 12 keys |
| Display | 32 character LCD |
| Power requirements | Two AA cells (included) |
| Operating distance | 1000 feet (Clear line of sight) |
| Receiver Output | One BNC connector (2 loads with up to 1000 ft. coax each) |
| Operating temperature | 0°F to 150°F |
| Certifications | FCC part 15 Class B, CE, RoHS |